|
|
| |
| STD-302N-R
434MHz/869MHz |
Regulatory compliance of the STD-302N-R
The STD-302N-R is designed for embedding in other equipment.
(Products incorporating the STD-302N-R are henceforward referred
to as final products.)
The European regulation applicable to the STD-302N-R is the R&TTE
Directive 1999/5/EC.The conformity assessment for the STD-302N-R
was completed in accordance with the R&TTE Directive Annex III
procedures.
Note: The STD-302N-R is intended to be used in all EU and EFTA
countries.
For 434MHz band, there may be restrictions on the use of voice and
audio applications in the following countries; FI, FR, HU, IT, LU,
LI, CH.
For 869MHz band, there may be restrictions on the use of the
equipment in the range of 869.3 to 869.4 MHz in the following
countries; CY, CZ, FR, GR, IE, IT, LV, LT, PL, SI, SE.
Cautions related to regulatory compliance when embedding the
STD-302N-R
1. Duty cycle
The STD-302N-R is designed to be used for the Non-Specific Short
Range Devices defined in the ERC/REC 70-03 Annex 1.
The STD-302N-R continuously emits carrier signals when power is
supplied. The user must design the final product to meet the
requirements of the duty cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC 70-03.
2. Antenna
The STD-302N-R is supplied without a dedicated antenna and the
user is required to provide an antenna. The conformity assessment
of the STD-302N-R was performed using Circuit Design’s standard
antenna ANT-LEA-01(434MHz)/-02(869MHz)
(1/4 lambda lead antenna), so we recommend using the ANT-LEA antenna
or an antenna with equivalent characteristics and performance. If
you use an antenna other than the recommended antenna, further
radio conformity assessment may be required.
3. Supply voltage
The STD-302N-R should be used within the specified voltage range
(3.0 V to 5.5 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the
STD-302N-R should be mounted on the circuit boards of the final
products and must be enclosed in the cases of the final products.
No surface of the STD-302N-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final product incorporating the R&TTE assessed STD-302N-R will be
exempted from its conformity assessment procedures. For details of
how to use the conformity assessment of the STD-302N-R, please
consult the relevant authorities or accredited certification
bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not
necessary if the final product is used in the harmonized frequency
band and is classified as Class-1 equipment. If the final product
is not used in the harmonized frequency band and is classified as
Class-2 equipment, the manufacturer of the final product has a
duty to notify the relevant radio regulatory authorities in the
countries where the final product is sold.
*NOTE: In case the STD-302N-R 434MHz is used with more than a 10%
duty, notification of the final product will be required. A list
of Class-1 equipment is available at
http://www.ero.dk/
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries. |
|
| STD-302N-R
419MHz |
STD-302N-R 419 MHz was designed to be installed in radio equipment for use in China. However this product has not been assessed for conformity with the appropriate local regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of
'STD-302N-R 419MHz operation guide'. |
|
| STD-302N-R
447MHz |
STD-302N-R 447 MHz was designed to be installed in radio equipment for use in Korea. However this product has not been assessed for conformity with the appropriate local regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of
'STD-302N-R 447MHz operation guide'. |
|
| STD-302N-R
429MHz |
STD-302N-R 429 MHz was designed to be installed in radio equipment for use in Japan and to meet the specifications of STD-T67. However this product has not been assessed for conformity with the regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
You can find more Japanese regulatory information at Compliance Assessment. |
|
| STD-302N-R
458MHz |
STD-302N-R 458 MHz was designed to be installed in radio equipment for use in UK and to meet the specifications of EN300 220-1 V.1.3.1. However this product has not been assessed for conformity with the regulations. Users are required to verify that their final product meets the appropriate specifications and to perform the procedures for regulatory compliance.
For more information, refer to the regulatory compliance information of
'STD-302N-R 458MHz operation guide'.
|
|
STD-302N-R 335MHz |
STD-302N-R 335 MHz was designed to be installed in
crane remote control systems for use in India. However this
product has not been assessed for conformity with the appropriate
local regulations. Users are required to verify that their final
product meets the appropriate specifications and to perform the
procedures for regulatory compliance. For more information,
refer to the regulatory compliance information of 'STD-302N-R 335
MHz operation guide'.
|
|
|
|
|
