 |
 |
| CDP-TX-02E(P)-R
434MHz CDP-RX-02E(P)-R 434MHz |
|
 |
| |
Regulatory compliance of the CDP-TX-02E(P)-R
and the CDP-RX-02E(P)-R
the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R are designed for
embedding in other equipment. (Products incorporating the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R are henceforward referred
to as final products.)
The European regulation applicable to the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R is the R&TTE Directive 1999/5/EC.The conformity
assessment for the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R was
completed in accordance with the R&TTE Directive Annex II (RX) and
III (TX) procedures.
Note: The CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R are intended to
be used in all EU and EFTA countries.
There may be restrictions on the use of voice and audio
applications in the following countries; FI, FR, HU, IT, LU, LI,
CH.
Cautions related to regulatory compliance when embedding the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R
1. Duty cycle
The CDP-TX-02E(P)-R is designed to be used for the Non-Specific
Short Range Devices defined in the ERC/REC 70-03 Annex 1.
The CDP-TX-02E(P)-R continuously emits carrier signals when power
is supplied. The user must design the final product to meet the
requirements of the duty cycle as provided in the Regulatory
parameters related to Annex 1 of the ERC/REC 70-03.
2. Antenna
The CDP-TX-02E(P)-R is supplied with a dedicated antenna and the
conformity assessment of the CDP-TX-02E(P)-R was performed using
the dedicated antenna (Circuit Design’s standard antenna
ANT-LEA-01, 1/4 lambda lead
antenna). If you use an antenna other than the delicated anntena
or an antenna with equivalent characteristics and performance,
further radio conformity assessment may be required.
3. Supply voltage
The CDP-TX-02E(P)-R should be used within the specified voltage
range (3.0 V to 12 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R should be mounted on the
circuit boards of the final products and must be enclosed in the
cases of the final products. No surface of the CDP-TX-02E(P)-R and
the CDP-RX-02E(P)-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final product incorporating the R&TTE assessed CDP-TX-02E(P)-R and
CDP-RX-02E(P)-R will be exempted from its conformity assessment
procedures. For details of how to use the conformity assessment of
the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R, please consult the
relevant authorities or accredited certification bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not
necessary if the final product is used in the harmonized frequency
band and is classified as Class-1 equipment. If the final product
is not used in the harmonized frequency band and is classified as
Class-2 equipment, the manufacturer of the final product has a
duty to notify the relevant radio regulatory authorities in the
countries where the final product is sold.
*NOTE: In case the CDP-TX-02E(P)-R 434MHz is used with more than a
10% duty, notification of the final product will be required. A
list of Class-1 equipment is available at
http://www.ero.dk/
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries.
|
| CDP-TX-02E(P)-R
458MHz CDP-RX-02E(P)-R 458MHz |
 |
Regulatory compliance of the CDP-TX-02E(P)-R and
the CDP-RX-02E(P)-R
the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R are designed for
embedding in other equipment. (Products incorporating the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R are henceforward referred
to as final products.)
The European regulation applicable to the CDP-TX-02E(P)-R and the
CDP-RX-02E(P)-R is the R&TTE Directive 1999/5/EC.The conformity
assessment for the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R was
completed in accordance with the R&TTE Directive Annex II (RX)
and III (TX) procedures.
The CDP-TX-02E(P)-R 458MHz and the CDP-RX-02E(P)-R 458MHz are
designed to be used in the 458MHz band allocated for Industrial or
commercial telemetry and telecommand devices in UK. The applicable
technical specification is EN 300 220.
Cautions related to regulatory compliance when embedding the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R.
1. Antenna
The CDP-TX-02E(P)-R is supplied with a dedicated antenna and the
conformity assessment of the CDP-TX-02E(P)-R was performed using
the dedicated antenna (Circuit Design’s standard antenna
ANT-LEA-01, 1/4 lambda lead antenna). If you use an antenna other
than the dedicated anntena or an antenna with equivalent
characteristics and performance, further radio conformity
assessment may be required.
2. Duty cycle
The CDP-TX-02E(P)-R 458MHz continuously emits carrier signals when
power is supplied. The user must design the final product to meet
the requirements of the duty cycle as provided in the relevant
regulations.
3. Supply voltage
The CDP-TX-02E(P)-R should be used within the specified voltage
range (3.0 V to 12 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the
CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R should be mounted on the
circuit boards of the final products and must be enclosed in the
cases of the final products. No surface of the CDP-TX-02E(P)-R and
the CDP-RX-02E(P)-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final product incorporating the R&TTE assessed CDP-TX-02E(P)-R and
CDP-RX-02E(P)-R will be exempted from its conformity assessment
procedures. For details of how to use the conformity assessment of
the CDP-TX-02E(P)-R and the CDP-RX-02E(P)-R, please consult the
relevant authorities or accredited certification bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not
necessary if the final product is used in the harmonized frequency
band and is classified as Class-1 equipment. If the final product
is not used in the harmonized frequency band and is classified as
Class-2 equipment, the manufacturer of the final product has a
duty to notify the relevant radio regulatory authorities in the
countries where the final product is sold.
* A list of Class-1 equipment is available at http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries.
|
|
|
|
|
