| CDP-TX-05M-R/CDP-RX-05M-R 434 MHz/869 MHz |
 |
Regulatory compliance of the CDP-TX-05M-R and the CDP-RX-05M-R
The CDP-TX-05M-R and the CDP-RX-05M-R are designed for embedding
in other equipment. (The products incorporating the CDP-TX/RX-05M-R
are henceforward referred to as final products.)
The European regulation applicable to the CDP-TX-05M-R and the
CDP-RX-05M-R is the R&TTE Directive 1999/5/EC. The conformity
assessment for the CDP-TX-05M-R and the CDP-RX-05M-R was completed
in accordance with the R&TTE Directive Annex II (RX) and III (TX)
procedures, and the Declaration of Conformity is attached to this
manual.
Note: The CDP-TX-05M-R and the CDP-RX-05M-R are intended to be
used in all EU and EFTA countries.
There may be some restrictions in the following countries. For
details, consult the relevant authorities;
434MHz : FI, FR, HU, IT, LU, LI, CH 869MHz: RU, IT, HU,FR, NO, CZ,
GR, LV, SK, MK
Cautions related to regulatory compliance when embedding the CDP-TX-05M-R and the CDP-RX-05M-R
1. Duty cycle
The CDP-TX-05M-R is designed to be used for the Short Range
Devices (Non-specific SRD & Alarms) defined in the ERC/REC 70-03.
The CDP-TX-05M-R continuously emits carrier signals when power is
supplied. The user must design the final product to meet the
requirements of the duty cycle as provided in the Regulatory
parameters related to the ERC/REC 70-03.
2. Antenna
The CDP-TX-05M-R is supplied without a dedicated antenna and the
user is required to provide an antenna. The conformity assessment
of the CDP-TX-05M-R was performed using Circuit Design’s standard
antenna ANT-LEA-01 (1/4 lambda lead antenna). Therefore we
recommend you using the ANT-LEA-01 antenna or an antenna with
equivalent characteristics and performance. For details about our
standard antenna, refer to
www.circuitdesign.jp or contact us. If you use an antenna
other than the recommended antenna, further radio conformity
assessment may be required.
3. Supply voltage
The CDP-TX-05M-R should be used within the specified voltage range
(2.2 V to 5.5 V).
4. Enclosure
To fulfill the requirements of EMC and safety requirements, the
CDP-TX-05M-R and the CDP-RX-05M-R should be mounted on the circuit
boards of the final products and must be enclosed in the cases of
the final products. No surface of the CDP-TX-05M-R and the
CDP-RX-05M-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the
conformity assessment procedures of the final product in
accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2
(Efficient use of the radio spectrum), the manufacturer of the
final product incorporating the R&TTE assessed CDP-TX-05M-R and
CDP-RX-05M-R will be exempted from its conformity assessment
procedures. For details of how to use the conformity assessment of
the CDP-TX-05M-R and the CDP-RX-05M-R, please consult the relevant
authorities or accredited certification bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not
necessary if the final product is used in the harmonized frequency
band and is classified as Class-1 equipment. If the final product
is not used in the harmonized frequency band and is classified as
Class-2 equipment, the manufacturer of the final product has a
duty to notify the relevant radio regulatory authorities in the
countries where the final product is sold.
The list of Class-1 equipment is available at
http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above
mentioned information about the conformity assessment and
notification of the final product. Directives, technical
standards, principles of operation and the like may be interpreted
differently by the authorities in each country. Also the national
laws and restrictions vary with the country. In case of doubt or
uncertainty, we recommend that you check with the authorities or
official certification organizations of the relevant countries.
|
|
|
|
|
|
