Regulatory compliance of the CDT-TX-02M-R and the CDT-RX-02M-R
The CDT-TX-02M-R and the CDT-RX-02M-R are designed for embedding in other equipment. (The products incorporating the CDT-TX/RX-02M-R are henceforward referred to as final products.)
The European regulation applicable to the CDT-TX-02M-R and the CDT-RX-02M-R is the R&TTE Directive 1999/5/EC. The conformity assessment for the CDT-TX-02M-R and the CDT-RX-02M-R was completed in accordance with the R&TTE Directive Annex II (RX) and III (TX) procedures, and the Declaration of Conformity is attached to this manual.
The receiver category of the CDT-RX-02M-R is Category 2.
Note: The CDT-TX-02M-R and the CDT-RX-02M-R are intended to be used in all EU and EFTA countries.
There may be some restrictions in the following countries. For details, consult the relevant authorities; FR, GEO, RUS, UKR.
Cautions related to regulatory compliance when embedding the CDT-TX-02M-R and the CDT-RX-02M-R
- Duty cycle
The CDT-TX-02M-R is designed to be used for the Short Range Devices (Non-specific SRD) defined in the ERC/REC 70-03.
The user must design the final product to meet the requirements of the duty cycle as provided in the Regulatory parameters related to the ERC/REC 70-03.
- Antenna
The CDT-TX-02M-R is supplied with a dedicated antenna. The conformity assessment of the CDT-TX-02M-R was performed using Circuit Designﾕs standard antenna ANT-LEA-01 (1/4 lambda lead antenna). Therefore we recommend you using the ANT-LEA-01 antenna or an antenna with equivalent characteristics and performance. For details about our standard antenna, refer to www.circuitdesign.jp or contact us. If you use an antenna other than the recommended antenna, further radio conformity assessment may be required.
- Supply voltage
The CDT-TX-02M-R should be used within the specified voltage range (2.2 V to 12 V).
- Enclosure
To fulfill the requirements of EMC and safety requirements, the CDT-TX-02M-R and the CDT-RX-02M-R should be mounted on the circuit boards of the final products and must be enclosed in the cases of the final products. No surface of the CDT-TX-02M-R and the CDT-RX-02M-R should be exposed.
Conformity assessment of the final product
The manufacturer of the final product is responsible for the conformity assessment procedures of the final product in accordance with the R&TTE Directive.
As to the conformity assessment of the R&TTE Directive Article 3.2 (Efficient use of the radio spectrum), the manufacturer of the final product incorporating the R&TTE assessed CDT-TX-02M-R and CDT-RX-02M-R will be exempted from its conformity assessment procedures. For details of how to use the conformity assessment of the CDT-TX-02M-R and the CDT-RX-02M-R, please consult the relevant authorities or accredited certification bodies.
Notification of the final product
The notification required by R&TTE Directive Article 6 (4) is not necessary if the final product is used in the harmonized frequency band and is classified as Class-1 equipment. If the final product is not used in the harmonized frequency band and is classified as Class-2 equipment, the manufacturer of the final product has a duty to notify the relevant radio regulatory authorities in the countries where the final product is sold.
The list of Class-1 equipment is available at http://www.ero.dk/.
Exemption clause
Circuit Design, Inc does not guarantee the accuracy of the above mentioned information about the conformity assessment and notification of the final product. Directives, technical standards, principles of operation and the like may be interpreted differently by the authorities in each country. Also the national laws and restrictions vary with the country. In case of doubt or uncertainty, we recommend that you check with the authorities or official certification organizations of the relevant countries.
|
